Guide

How to Secure a Ring Doorbell From Theft

Updated on · By the Wireless Doorbell Store team

Secure a Ring Doorbell from theft by mounting it in a locked anti-theft housing and placing it out of easy reach. A no-drill clamp-on mount covers the body and blocks prying, so the doorbell stays put without screws in your door or wall.

On this page (9 sections)
  1. Why are Ring Doorbells a target for theft?
  2. How does an anti-theft mount secure a Ring Doorbell?
  3. Which mount is best for renters and apartments?
  4. Where should you place a Ring Doorbell to reduce theft risk?
  5. Does a security sign or sticker help deter theft?
  6. How do you set up a Ring Doorbell so it's harder to steal?
  7. What should you do if your Ring Doorbell gets stolen?
  8. How do you keep the mount and doorbell secure over time?
  9. What else should you add to a Ring Doorbell security setup?

To secure a Ring Doorbell from theft, mount it in a full-coverage anti-theft housing and keep it out of easy reach. A no-drill clamp-on mount wraps the doorbell body and blocks prying, so it stays on the door without screws.

Pair that with sensible placement and you make your doorbell a much harder target.

The goal is simple: raise the effort and lower the reward. A doorbell that lifts off in two seconds is a gift to a passerby.

One locked inside a housing, mounted above shoulder height and watched by the camera itself, is a different story.

Why are Ring Doorbells a target for theft?

Battery-powered Ring Doorbells clip onto a bracket and lift off in seconds, which is why they get stolen. The camera is valuable, and the quick-release design that makes charging easy also makes removal easy.

Most thefts are opportunistic. Someone walking past sees a small camera within arm's reach and pops it off.

There is rarely planning involved, just speed and low risk.

That matters for how you respond. You don't need a bank-vault setup.

You need to remove the easy grab and add a visible layer that makes a thief move on to a simpler door.

A Ring Doorbell that sits at chest height beside a busy sidewalk is the worst case. A doorbell set higher, tucked back from the street and covered by a housing, is far less appealing.

How does an anti-theft mount secure a Ring Doorbell?

A full-coverage housing clamps around the doorbell and covers its release points, so the unit can't simply be lifted off. The Dukoyb mount uses a 360° all-round design that protects against theft, prying and accidental knocks.

It installs without drilling, screws or tools. An adjustable clamp fits most door thicknesses, with a soft foam pad to protect the door from scratches.

You can remove and reposition it whenever you need to.

The housing is cut to keep the motion sensor and camera view open. That matters, because a mount that covers the lens defeats the point of having a camera.

Compatibility is the part to check first. The mount fits the newest battery Doorbell, Battery Doorbell Plus and Battery Doorbell Pro (2nd Gen), plus the Blink Video Doorbell Gen 1.

It does not fit Video Doorbell 1, 2, 3, 3 Plus or 4 from the 2020 releases, Blink 2nd Gen, or any wired doorbell.

Door fit matters too. It only works on left and right in-swinging doors with flat edges, from 0.8 to 2.3 inches thick, with a gap over 0.06 inch.

It won't suit out-swinging doors, iron doors, screen doors or uneven edges.

Which mount is best for renters and apartments?

A no-drill clamp mount is the best fit for renters, because it needs no holes and comes off cleanly. That keeps your security deposit safe while still adding real theft protection.

For a rental, avoid anything that requires drilling into the door or frame. Landlords rarely welcome holes, and patching them costs time and money when you move out.

A clamp-on housing avoids the whole problem.

The clamp design also helps if you move. You loosen it, take the doorbell and mount with you, and reinstall at the next place in seconds.

No tools and no repair.

If you have a smooth wall beside the door and prefer adhesive over a clamp, the Ring No Drill Mount is the maker's own option. It uses a strong non-damaging adhesive and removes by pulling the adhesive strips.

Ring says the adhesive works best on smooth, even surfaces. Rough brick, shingles or rough stucco will weaken the grip.

It's compatible with the Battery Doorbell 2nd Gen, Battery Doorbell Plus 2nd Gen and Battery Doorbell Pro 2nd Gen.

Adhesive holds the doorbell to the wall, but it doesn't cover the body against prying. If theft is your main worry, the clamp housing does more.

A no drill mount is the better pick when you want zero wall damage and already have a safe spot.

Where should you place a Ring Doorbell to reduce theft risk?

Mount the doorbell above shoulder height and away from the street edge, so it's hard to reach and easy to see. Height is the cheapest theft deterrent you have.

A doorbell at chest level next to a public sidewalk invites a grab. Raise it to about 48 to 60 inches from the ground on a typical door, which is still low enough for visitors to reach the button and high enough to be awkward to snatch.

Angle it toward the approach path rather than straight out. A camera that captures faces coming up the walk is more useful, and the housing is less exposed from the side.

Keep the doorbell clear of bins, fences and low walls that give someone a step up. Trim shrubs that hide the approach.

A lit porch also helps, because most doorbell thefts happen in dim light.

If you rent and can't move the mount, use the clamp housing and aim the camera well. Placement plus coverage is the realistic combination for most apartment doors.

Does a security sign or sticker help deter theft?

A visible security sign or camera sticker helps a little, but it's a backup, not the main defense. A sign warns a casual thief, but it won't stop someone who has already decided to grab the doorbell.

The doorbell camera itself is the stronger deterrent. A housing makes the camera obvious and hard to remove, which sends a clear message.

A small "video monitored" sticker under the doorbell reinforces it.

Don't rely on the sign alone. It does nothing to stop the physical lift-off.

The housing does that.

The real value of a sign is early warning. It may push a thief toward an easier house on the street.

That is worth having, as long as the physical security is real too.

How do you set up a Ring Doorbell so it's harder to steal?

Follow the mount's steps, tighten the clamp fully, and test that the doorbell won't budge before you call it done. Loose hardware is the weak point in any setup.

  1. Check your doorbell model against the mount's compatibility list.
  2. Measure your door thickness and edge before buying.
  3. Fit the housing or clamp and tighten until the doorbell is firm but not crushed.
  4. Confirm the lens and motion sensor are uncovered.
  5. Open the Ring app and check the live view and motion alerts still work.

The Dukoyb mount includes the housing, a screw kit, a screwdriver and a user manual. Follow the manual's fit steps and keep the foam pad against the door.

For a battery model, you'll remove the doorbell now and then to charge it. A battery charging routine that keeps a spare pack ready means less time with the doorbell off the door.

A quick-release battery pack lets you swap power without removing the unit.

The Ring Quick Release Battery Pack works with battery-powered Ring doorbells and cameras, including the Battery Doorbell Plus and Pro. Its quick-release tab lets you change the battery without moving the device.

That means your anti-theft mount stays tight and in place.

What should you do if your Ring Doorbell gets stolen?

Report it to the police and your insurer, then check your footage and account settings. Speed matters, because the camera may have captured the thief on the way in.

Open the Ring app and review motion events from the time window. Save or download any clip before it rolls off the history.

The footage is often the best evidence you'll have.

Change your Ring account password and remove the stolen device from your account. That stops anyone from linking it to a new account.

If you had a Ring Protect plan, check what it covers.

File a police report with the serial number if you have it. The box or app usually shows it.

Many insurers ask for a report before paying a claim.

After that, replace the doorbell and this time add the housing and better placement. The goal is to make the next attempt fail.

How do you keep the mount and doorbell secure over time?

Check the clamp and the mount every few weeks, especially after storms or a lot of door traffic. A loose mount is easier to pry and easier to knock off by accident.

Wipe the housing and lens with a soft cloth. Dirt and spider webs blur the view and can hide a loosening clamp.

Tighten anything that feels loose.

In hot or cold weather, adhesive can weaken. If you use the Ring No Drill Mount on a smooth wall, press it firmly again or move to a clamp housing if it starts to lift.

Keep a spare battery charged so you're not leaving the doorbell off the mount for long. A doorbell sitting on a table waiting to charge is easy to forget and easy to steal.

What else should you add to a Ring Doorbell security setup?

Start with the housing as your main physical defense, then build around it. A few extras make the whole setup more reliable without adding much cost.

Compare Ring doorbell accessories if you want to round out the kit. A spare battery and a solid mount cover most of what you need.

If you use Apple devices, check whether a Ring Doorbell works with Apple HomeKit before you plan around it. It helps to know what your smart home can control.

The clear decision rule for how to secure a Ring Doorbell from theft: pick the clamp-on anti-theft housing for most doors, because it covers the body and needs no drilling. Choose the Ring No Drill Mount only for a smooth wall where you want adhesive and zero holes.

Add a spare battery so you spend less time with the unit off the door.

Frequently asked questions

Does Ring sell an official anti-theft mount?

Ring sells its No Drill Mount, which attaches a compatible battery doorbell to the wall with adhesive and removes without damage. It holds the doorbell firmly in place but is not a full anti-theft housing.

For coverage against prying, pair it with a third-party locking mount that wraps the doorbell body.

Will an anti-theft mount block the motion sensor?

A well-made mount leaves the motion sensor and camera lens open. The Dukoyb housing is shaped so the lens and sensor stay uncovered.

Check the mount's cutouts line up with your model's sensor window before you tighten the clamp.

Can a thief still remove a doorbell from an anti-theft mount?

Nothing makes a doorbell impossible to remove, but a clamp-on housing adds time and effort. Most opportunistic thefts target exposed doorbells that lift off easily.

A covered mount plus a less reachable spot makes your doorbell a poorer target than the one next door.

Does renters insurance cover a stolen Ring Doorbell?

Many renters and homeowners policies cover theft of personal property, including a doorbell, subject to your deductible. Check your policy before you rely on it.

Keep the receipt and a photo of the installed doorbell so a claim is easier to file.

Should I use screws or adhesive for a rental?

Adhesive or a clamp-on mount is the better choice for a rental, because neither leaves holes you have to patch. A clamp-on anti-theft mount needs no screws at all.

Keep the original bracket so you can restore the door when you move out.